Search results

Guys you have to be comfortable with disassembly down to the individual head components but I posted a solution I found here http://signs101.com/forums/showthread.php?p=857660#post857660 I will add that once you get down to the head only with the manifold removed, if you catch the light just...

Can I be so bold as to assume solvent acrylic with solvent acrylic inks and water based acrylic with aqeous inks?

Gorgeous looking work, would love to know if you're doing any preparation to the timber as an inkjet receptor layer

Would just like to share my success in case it helps others. I was getting an Error07 _____*__ on my JV22. Brief rundown; Tried the cable swaps with the next adjoining head as well as swapping the cables between left/right & top bottom between the same position in the slider board. No...

Vinylman - Champion! - thank you, I was working my way backwards through his posts, but didn't get that far back

+1 great work subscribing so I can find this thread again easily

Some time ago I saw a thread in which you had pics of some small Y tube adaptors so that you could easily switch inks with the connection of the alternate lines close to the dampers. Tried to find the thread earlier today, but failed. Can you point me to the thread and give any info on where...

I'm still using AVGFree and haven't noticed any slowdown associated with it, though I'll keep a lookout Mike Lin's startup contol is a great tool http://www.mlin.net/StartupCPL.shtml That in combination with checking which services are loading automatically is a good start Right click My...

Well spotted, I did mean JV3 service manual, though I haven't yet needed to refer to it, though the proper JV22 service manual will be a bonus. The error followed the head whne I switched the cables, so the prognosis (my assumption) is that it's one side (same side) of the head. I switched the...

My understanding is that the manifold on a solvent head is different (no direct experience of this - just from what I've read) so you should be able to buy the Fj heads, change the manifold to a solvent resistant one and you'd be good to go...BUT please don't take my word for it, wait till...

I have finally had some time to get the new dampers installed and everything checked and cleaned, polished and generally looking schmick (aussie slang for great!) So I powered her up, it went through the motions and then I get Head Error 07 -----*-- So I've done some research and it seems to...

I was reading somewhere just the other day (forgot to bookmark it) and noticed two quoted different viscosity figures for aqueous dye and pigments, dye was from 1.78 - 1.98 and pigment was from 1.95 - 2.20 small differences, but differences nonetheless. Presumably higher viscosity ink will...

Just checked recent emails from parts suppliers and I should add that asking for either F056000 and F056010 came back negative so try F056030 and f056030, they are the same part but it seems the earlier revisions have been deprecated

Fairly certain that uses the same heads an the Epson 3000, F055110 is an updated/later version for the colour head also used in the 7000 and 9000 These are DX2 heads Check this page for reference on the colour heads...

That's sad to hear, but confirmation of what you had suspected if that is any consolation... BTW a local electronics repair shop may be able to replace any damaged power components if they are able to read the laser etching or resistor codes

For the SCSI VOODOO always start with the cables and terminators and if the SCSI BIOS is giving problems, then re-seating the card or trying another slot is worth a shot. Almost all SCSI, with the exception of U320 is considered legacy at this point, so I think you may have issues with drivers...

Hi all, Just picked up a JV22-160 for cheap as it had been sitting unused for about 18 months. I've got the heads sitting soaking to loosen any clogs and have replacements dampers on their way to me. Four of them had air leaks in the clear plastic sides. So I am assuming that when the...

You may well benefit from walking away from it for a couple of hours and doing somerhing else that occupies your mind entirely. When you come back to it approach it from an entirely different angle, so walk up to it from the left side instead of right, or vice versa. I once couldn't get an...

Try reversing the flow - What I mean by that is instead of say pulling a vacuum at the end of the pump lines, put some cleaning fluid on the parking pads to avoid gunk going backwards into the heads - then move the heads to park position and paint suspect or potential seal areas with liquid soap...

Hi All, I've been registereed here for a while and been lurking from a little while longer than that, been waiting to get a printer so that I can introduce myself. My background is Professional Photography and I've just managed to acquire a Mimaki JV22-160 that can hopefully do my film and drum...