• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. Roland printer data cables

    Blown fuses on the mainboard; blown heads, blown print carriage board from a possible short when the cables were crammed. Start by checking fuses.

  3. Networking a Mimaki CG160 FX?

    USB to Ethernet Cable maybe. Set up your cutter with an internal IP Address...

  4. Happy Bithday Gino!

    Happy Birthday Gino

  5. Roland 540sc

    Power the unit off... and unplug. then lower the captops manually. Move the heads to the right slightly to unlock the carriage and then move them to the left over the platen. Clamp off the lines going to your pumps. Fill the caps with cleaning fluid and move the printhead carriage back into...

  6. Flexi 7.6 vertical offset in cut/plot adding in numbers

    What version of Operating System do you have installed? Was it recently updated? Open you production manager and Add Setup of the same device using the same port... when prompted for name of this new setup, name it something unique to differentiate from the first device. Then delete the...

  7. ssmmgr.exe???

    Samsung Printer Ink Monitor program.... Have a samsung printer installed? or at one time did you?

  8. crop not found roland sp 540V

    Is it possibly scratched? Or hazy from the laminate?

  9. What cutter to buy

    The only issues... ONLY issues I had with Summa were related to the power supply on the D60 and D60u units. The 'S' and 'T' Series have always been ROCK solid. IMO

  10. What cutter to buy

    Graphtec FC2100-60 and Gerber 4b :) (CASmate for DOS too)

  11. Problems with Graphtec ce5000-60 and flexi

    Just glad I was able to help out. Signs101 rocks.

  12. Drytac JM54

    If you replaced the fuses and still no power.... the power board may be damaged. Contact DryTac

  13. Software / Equipment Purchase - What seals the deal?

    Was taking the apples vs. apples kind of approach in relation to the software and equipment... you want Graphtec Cutter, quality not a factor when comparing one supplier to another. See your point if we were talking Flexi vs. CiberCut or Graphtec vs. Redsail cutter.

  14. Roland SC-540 print/cut problems

    Did not mean that you were wasting anyones' time. Sorry if it seemed to be implied. I really meant, has the print/cut error been happening for a while, always, or just today? Have you tried to send only one copy to see if it completes? Sounds like something is amiss in the RIP settings. One...

  15. Roland SC-540 print/cut problems

    Reload default prefs and setup device again in PM. Been doing this a while?

  16. Roland SC-540 print/cut problems

    When you save in illustrator as eps, you should have option for version compatibilty. Correct?

  17. Roland SC-540 print/cut problems

    Export or save as illy eps version CS and try

  18. Roland SC-540 print/cut problems

    Are the EPS files created from Illustrator? If so, which version?

  19. Cleaning Cartridges question

    Dropout can many times be attributed to captops not sealing well... have you replaced them?

  20. How often does the encoder strip need to be replaced on an SP-540

    Clean your printer on a regular basis. You may have an overspray problem or possibly the cut trailing cable has a lot of ink and metal dust built up on it. Be careful installing yourself.... these can be scratched relatively easy.

  21. Cleaning Cartridges question

    Do you mean you want to do a Head Wash? If so, be prepared to waste a good bit of ink. In USER Mode, select Head Wash and it will prompt you where to put the cartridges. Beware, once you start a Head Wash, you have to let the printer run its course. Make sure you have enough cleaning carts...
Top