Search results

I think the silvering is a pressure issue. If you run your fingernail across the affected area, you'll find it probably comes out. It usually comes out on it's own overnight, so if it's 5 days then I don't know. I don't have this machine but, I don't think there should be a space. If the chain...

Enough of the technical stuff. I'm stupid when it comes to making profiles and adjusting things. But I do know about the everyday running of the machine. First, I had a Roland Versacamm. We bought the Hp 360 about 8 mos. ago We decided to buy the 360 over the 310 because they said it was...

Been asked to quote prints on 90# matte finish posters Not sure what 90# is. My supplier keeps telling me his stuff is 8 mil or 10 mil or 17mil How do I know how thick 90# is ? I'm not even sure if it's supposed to be paper. Maybe they want foam board or pvc The customer is a bakery and is...

Thank You both

I notice on cold days, the windows fog up with a film and doesn't go away unless you clean it off Is this whats going into my lungs

I printed a sample of Pos Pro 200 on the 360. The leading edge curled up when it came out of the heater. Wasn't too bad but after it laying on the table overnight, the entire print was curled liked a pretzel making it unusable. I printed it on the Versacamm, but I want to fade out using this...

Think I remember it to be pretty inexpensive. 50 - 75.00 I think I remember it to be easy to install as well And I agree, this would be my first step for the problem

Thanks Brad... some very good ideas and comments

Does anyone know where to buy a small amount of optically clear double sided tape ? I don't see it in Fellers and my local supplier doesn't have it Thanks

Stouse ? or 4 over?

Have you used them... are they any good It's at the request of a friend/ who does bomb proofing windows, so I haven't seen it. It's 6' tall x 50' wide. So I think it would be better with a frame

I'm looking for the Truck Frame Banner system. The type where you attach a frame all around the outside of the truck and then slide in the banner into the frame. Going to use it on a building, but I don't think that matters. I need a vendor that can do it. They also need to print the banner...

I'm sure you would need to replace the keypad. Seems Gerber would be the choice or the Plotter Doctor which may be a less expensive choice

Painting sounds so messy. Don't know if it would work any better but, there are rolls of glue that you apply like you were laminating to the board. Then mount the print to the board. Maybe worthwhile looking into.

I had my Roland for 10 years. I never had a contract. I'm not saying you shouldn't have one... especially for piece of mind. Over the 10 years, I needed to change the head 3 times. A couple of small items like the encoder strip and cleanings. I think over all I saved a bit of money. My advice...

4imprint.com Just did some pens for myself. Very high quality I'm sure they would send you some samples

I can understand using 3m cast with a printed job, but what do you use on a box truck when it's mostly cut vinyl. You still have the problems with rivets. You can't print a simple phone number and put it on just because of rivets. That would be one expensive job. do you use calandared ...

Is this what your looking for ? Made locally here Coyle & company Hauppague NY 631-780-7045 They can make any size or configuration Every time I'm in there, their making them by the hundreds Ask for Darrin Let me know if it works out

It's a HP l360... I also have a Versacamm that I can probably use,but I want to get the use from the new HP Thanks, I'll try it tomorrow

I'm trying to print reverse on Oracal 290 laminate. i can't find a profile made for it. I've tried a few stock ones, but I'm just wasting material. I'm struggling to just figure out how to print on it since it's translucent, but I'm getting there. I'm not clear on how to make it's own profile...