Search results

if your lead edge is not cut straight I have seen this. One solution is to simply not use the basket.

We use "Graphtec 4 Points Type 1". It sounds like that is what your plotter is looking for...

Brushed Silver Composite comes in 1/4" (aka 6mm)

If your unit uses bulbs, then yes they likely need replacing every 6-12 months. The newer LED versions have a separate unit that cools the unit and controls intensity of the lamps - so if you have a LED lamp unit, lamp intensity is likely set too low. Water should not dissolve cured UV inks...

Aluminum Composite is very durable for exterior use. It comes in different thicknesses: as a 3mm it is a great material to go on a wall or over a wooden face, but 3mm is too thin to withstand wind unsupported (like when used between two posts); 6mm or thicker will do much better between posts -...

They asked about installing it themselves... did the other shop exclude installation from the quote? That might be the difference in cost.

Gerber Edge 2 Gerber Envision Roland Soljet XR-640 Fluid Color R84 Turbo (4x8 Flatbed UV printer) Graphtec 5100-75 30"plotter Graphtec 9000-160 60" plotter CWT 1640 work table/cold laminator Fletcher Panel Saw

First, Trailing lamps are right dir_ L_Lamp checked, R_Lamp not checked, left dir L_Lamp not checked, R_Lamp checked Leading lamps is the opposite right dir_ L_Lamp not checked, R_Lamp checked, left dir L_Lamp checked, R_Lamp not checked Dual Lamps would have all four checked - but only use when...

Screen is the fineness of the dots - a lower number yields an image that is very sharp, a higher number yields an image best seen from far away. Ink density is essentially the amount of ink used to print. So 1x would be a normal amount. 2x is sometimes useful when printing on a sign that will be...

I would be more concerned about cleaners and detergents (shampoo, soap). You could always apply a clear or matter laminate over the graphic if need be.

I might not be back today to answer, but I'm sure we would all like to know what the issue is before making suggestions...

You often do need to delete some old jobs in Versa Works to bring in large files. Try cleaning it out of whatever is not needed and resend it.

We've used all three options as well. One thing I remember, when we did option 3 we one found that when you get near the end of a roll of the optically clear mounting adhesive, sometimes it would have a ripple/impression from where it had been taped to the roll and this would transfer to the...

Clean the area... the dust is coming from somewhere in your shop. Maybe the floor as you walk; maybe from using a panel saw and the dust is still floating in the air. I would suggest you clean the table and the floors, use a tack roller on the substrate, do your material prep (cutting substrate...

For decals wrap vinyl is not so good, but those with Rapid Air/Air release work great. We use Avery MPI1105 EZ for decals or Oracal 3951RA. For Wraps, Avery MPI 1005 EZRS, Oracal 3951 Pro Slide, Arlon SLX+ all work well. For laminate our favorite is OraGuard 290, though it is not inexpensive. A...

You will need to laminate them. As far as vinyl, Avery MPI 1005 EZ (and NOT the EZRS - repositionable needs to be post form heated, whereas EZ does not) is a good quality, readily available air release type vinyl with good initial tack and a good price. Avery sets the price on this, so it should...

I don't see the issue weeding this. But a tip is to put the cut on it and let it sit overnight before weeding - often the adhesive will pull away from itself a tiny bit where the vinyl is cut and be easier to weed.

Orafol 3621 Soft Calendared White Vinyl - it is removable and less than $200 for a 54"x50yd roll.

We usually print using our UV, but remember you can print onto vinyl and coat the magnets and then trim them out...

I'd offer him $3500, but that machine will pay for itself overtime.