• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. Anyone use Fellers Back Label Cast to wrap with?

    We wrapped a truck the other day using their cast kit. Overall it was pretty nice stuff. I liked the adhesive and air travel. Overall white point was good. Slidable for a few seconds, but definitely a higher initial tack. I do not like the clear adhesive as you can anything of contrasting...
  2. Laminator media buckling in the middle

    When do you roll to roll. Are you loading like this? Because I am currently loading over the feed table, wondering if this method would also help. Coming from a royal Sovereign manual laminator so we always fed over the flat loading piece not directly to the roller like these folks are doing.
  3. Laminator media buckling in the middle

    We just got an older seal laminator up and running. We are using it for roll to roll. However when feeding the media through. I'm seeing the middle buckle, almost bow out. I suspect the roller tension is more on the ends than the middle somehow? I know they have crowned rollers but people do...
  4. Seal 600 Roller Up/Down Switch

    Got to the bottom of it. The problem ended up being a power supply issue, unit was only getting 130volts! Not enough to trigger the 240volt relay!
  5. Seal 600 Roller Up/Down Switch

    I have a new to me Seal 600. It's pressurizing but when I flick the switch to drop the rollers, nothing is happening. I called a seal tech, he recommending replacing the Solenoid Valve, i've ordered one but any thing else I can try that may be stopping the switch from working?
  6. Need Help my Epson s60600 is having a random problem

    I had this same issue with my S40600. After a lot of trial and error I ended up having to switch to a network port, my USB port somehow started to have dataloss once I switched to the network port did not have that issue.
  7. Summa S2T 160 Erratic Feeding

    Thanks Phil! I will check these settings in the morning and check back!
  8. Summa S2T 160 Erratic Feeding

    Ever since new my Summa S2T 160 is overfeeding the matierial. It checks to see how much material is on the roll . It goes way past what it needs, then checks it again halfway though the job. Causing it sometimes to go slightly off. I've dealt with it for an about a year but now I'm really...
  9. Looking for a recyclable banner material

    I've been trying to find an eco friendly banner material that can be recycled! After some research I found UltraPoplin Soft Image D240 however after requesting a sample today, they informed me they no longer make this product. I do have an eco solvent printer that would be ideal to use I'm...
  10. Epson surecolor S40 vertical banding

    Been having this issue with my S40 for a few months now more noticeable on vibrant colors. They are somewhat evenly spaced. I’ve tried heavy cleanings, manual cleaning, replaced the damper pad. Not sure what else’s could be going on. Any help is greatly appreciated!
  11. Seeking Experienced installer/wrapper in New England

    Small wrap shop seeking experienced installer/wrapper in New England area for busy wrap shop.
  12. Where to buy SunTek films?

    I am looking to purchase SunTek films. Anyone have any recommendations on where to purchase by the foot?
  13. Cast Transfer Paper?

    I need to do some serious contour wrapping with a giant diecut sticker. Other then taking the paper off and working in each piece one by one. Anyone know of a "stretchy" cast like transfer?
  14. Vcarve cuts are cutting too deep

    I need some help. I am using Vcarve software and my cuts are cutting too deep. I have a 6mm material and need to cut 3mm deep . My cuts were going all the way through. As a test i’ve rolled the cut back to .25mm but still going way too deep. See attached, please help! Anyone see anything...
  15. NEWBY QUESTION. Vac Table

    I just got my first gantry 4x8 CNC. So sorry for the newby question. When routing on the vac table. How do we ensure we don't damage the wood? when doing full cut throughs?
  16. Vertical Lines on prints S40

    Brand new roll. Printing straight gray on it.
  17. Vertical Lines on prints S40

    I am having issues with vertical lines showing up on my prints all the sudden. Epson S40. 3 years old.
  18. FC8600 springs?

    thank you! I heard from Graphtec and they also suggested the calibrations which I did and it's working fine now!
  19. FC8600 springs?

    I have a FC8600 64". It's about 6 years old. After a pretty large perf cut job our cutter is acting up. It's dragging the knife across when setting up. Also not cutting all the way through any longer. Replaced the cutting strip. No difference. I pulled the cover off the head and found a...
Top