Search results

On the Acuity's you can run white at express, production or regular quality. It doesn't have to be quality-layered. By doing this you have to run one file as a white file and another as a CMYK file, but on wood you can easily get away with a production white and production CMYK and still be...

Is this an Acuity orr Oce Arizona printer? Check the ink supply line going to yellow, make sure it's firm like all the other colors.

The head is probably shot. Happened a couple times to me. I doubt it's the firewire cable, but if you already ordered one just plug it in up in the carriage, and go directly into the board by the PC. I wouldn't waste all that time routing it through the igus track just to find it it doesn't fix...

I've seen them on eBay a couple times.

^ If I had to guess, 258. Since that has the best adhesion. Also, I've had pretty much the exact same experience with our Acuity Advance (Arizona 360) as DougFastSigns. We went through so many heads on that machine for no reason. Heads would work fine one day and be completely dead the next...

Spray denatured alcohol on it and let it soak. Repeat then wipe off.

ZE 720 from Fuji is specifically designed for coroplast. Smells terrible though. Our Inca Onset S40 won't stick to coro.

Fuji has a adhesion promoter for coroplast (ZE720), acrylic (ZE680) and other plastics like styrene (ZE1000). There's also AP3155 and AP2155.

Might get something like this: https://www.amazon.com/O-Cedar-Hardwood-Floor-More-Microfiber/dp/B0000DAT86/ref=sr_1_7?ie=UTF8&qid=1468961815&sr=8-7&keywords=microfiber+floor+mop And some higher quality microfiber cloths. Also, I've tried using air, but that doesn't help get the fine particles off.

What's considered a high quality microfiber cloth?

The Matthew's Cleaner leaves the acrylic really smooth, which is somewhat easier to get the dust off of. But doing a full 4x8 sheet, it's difficult. I'm using poly wipes to clean the sheets. Might try a microfiber cloth?

Was wondering what others are using for cleaning sheets of acrylic for printing directly to it. I've tried 91/99% iso, 91% iso mixed with distilled water and Matthews plastic cleaner for cleaning it. The problem is, whatever you do you always have small dust particles left on the sheet. I've...

I demo'd one in Wisconsin, but ultimately we went with an Acuity F. Main reason being we already have an older model Acuity, so there was less learning curve. Seemed like a good machine, just more expensive.

I have leftover rolls of fabric material for sale. There are 2 types of fabric. Each are 10ft-8" wide and have 164ft on each roll. Fox 7.4oz Twill (6 rolls) - $550 a roll Fox 6.8 Front Lit (9 rolls) - $390 a roll Located in Muskegon MI. Will ship if buyer pays shipping.

This is a used carriage PCB board for an Acuity Advance or Oce Arizona 360 flatbed printer. The board works fine.We were told by tech support we had to replace the board to fix our problem, however it did not fix the problem, so we were left with a perfectly fine board. Part #: 3010113157...

These tables are for oversized boards on a flatbed or roll to roll printer. We used them for a roll to roll printer, and we fed through long sheets. Could be used for a hybrid printer as well.They are 13.5ft wide, and 15ft long with a 5ft extension. The tables can break up into four 3ft~...

Check the little plugs by the posts, on the 360 there should be a red light on the left and right motor.

Might have to try this with Fuji's ZE680 adhesion promoter for acrylic. Usually it leaves nasty streaks on the acrylic. I have some of the Matthew's Cleaner, so I'll try mixing the two. Thanks for this.

How many nozzles are out? I have this problem when I drop a lot of nozzles in the middle of the print. Does it drip on either the far left or right side? Usually it's because ink is accumulating on the printhead and the motion from the carriage going the other direction causes it drip.

I've had this happen with a Magenta and Yellow head a couple times. Both times they had to replace the head. Side note, did you have to attend the "class" to get your service key? If so do you know much it costs to go, and what the yearly cost for the key is? I've been wanting to go so I can...