• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. New XF-640 Banding Issue

    We have learned that when installing the XR's, we have to spend an extra hour or two dialing in the printheads and print/cut alignment using ONLY PET-G MATERIAL using a 25x-30x loupe. The precision at which these units have to be dialed in is very tight. As is the order in which you make the...
  2. Inks not blending on print?

    What brand of ink are you using? Is the heater working? What brands of vinyl have you tested? What software and profile?
  3. Roland Versacamm vs-300i - WRONG CARTRIDGE

    I am sure you pulled it out and tried it again getting the same error. Try pushing the edge of the cartridge a little towards the back of the printer (wiggle the cartridge) to see if it might be just a slight alignment/connection issue. If not, could be a defective chip. If you running Dual...
  4. Is our old Plotter shot or is this fixable?

    Without schematics and detailed knowledge of electronics and proper testing techniques, no. Which fuse was blown and do you have a pic of the repair?
  5. Flexi Designer demo?

    Let me know if you would like to remote into my PC and use mine for this one test... I can get you an older version to use as a demo, let me know.
  6. Vinyl Slitter

    smart slitters manufactures their own machines and are very good for entry level to medium production use. Heavy use will push you closer to $12-20k.
  7. Is our old Plotter shot or is this fixable?

    Boards are no longer available for this one if it is the PNC-960. Had one in our shop last week also blew the board. Some locations offer board level repair but even that is not always 100% cure, if there is another part causing the short such as trailing cable.
  8. Problems with GX24 Cutting

    Get a magnifying glass and look at the tip and leading edge of the blade... blade quality and the material being cut are variables that will determine the length of time the edge and tip of the blade remain sharp.
  9. Graphtec FC7000 Speed up manual feed of media?

    Had to hook the ole 7000mk2-130 to confirm, it is the NEXT key. Thanks tbullo
  10. Graphtec FC7000 Speed up manual feed of media?

    I think you can hold one of the other buttons down while holding the down arrow to make it go faster..... Problem: I forgot which one :) Checking manuals now.
  11. Problems with GX24 Cutting

    What does the Blade Protection Strip look like? Does is have a groove cut into the center of it? Have you taken the blade out and checked the tip and edge with magnifying glass to see if it is dull, chipped or otherwise damaged? Sounds to me like one or both of these are the issue. If so...
  12. Printhead Problem on VP540

    Not mechanical... electrical Possible culprets are damaged or loose connection of head ribbon cables, long print ribbon cables, print carriage board, mainboard or head. First do no harm... power off and unplug. Then disassemble and gently check all ribbon cable connections from the head to...
  13. Strange line on prints, need HELP!

    +1 for encoder scale / sensor (reader) - pic 2 Would be interested in seeing the nozzle test pattern on this one too. I would guess this unit needs a good going through to dial in all adjustments as well... bias, vertical, horizontal, bi-di
  14. GX-24 Not Cutting corners

    Thanks JMPrinting for registering on our E-Commerce website. I appreciate your consideration and hope I may be able to assist you further.
  15. GX-24 Not Cutting corners

    We offer the following items.. OEM and aftermarket http://www.cssignsupply.com/index.php?dispatch=categories.view&category_id=208
  16. Roland LEF-12 Dealer Demo Unit with BOFA System

    Roland LEF-12 (Purchased 6/19/14) - S/N: ZBO1331 Balance of 24 month Warranty Eco-UV Inks CMYK+Wh+Gl Roland Versaworks BOFA Air Filtration System Cabinet Local Pickup Only (Atlanta, GA Area) MSRP $24,164.00 Call for best price ... 1-877-602-4237 or local 678-735-3200 Ask for Bobby Fosson
  17. Roland versacamm sp300v white bleeding around letters

    When was the last time you checked the vertical and horizontal head adjustment calibration?
  18. Using AutoMark for Box Trucks Partial Wraps. Anyone else having great success?l

    We have several clients buying the Automark from us and we have not received any negative feedback or problems. The General Formulations products are very stable and competitively priced. With exception to a facestock problem on their 222 6mil semi rigid product, which has been resolved, we...
  19. Roland Ink supplier...

    Thank you for taking my call Tony.
  20. cutter isn't lifting back after sheet cut

    There is small spring in the mechanism that may have popped of...
Top