Search results

I'm a big fan of tactical pants. Can never have enough pockets.

That's what I'm thinking. I'll have to experiment a little. Nope. Only has 2 point at each corner when I looked in Illustrator.

I've got some stickers I'm doing kiss cuts of and the design is tapered because of the tube they are going on. For some reason whenever I cut them it runs about half the speed it's set to. It's something I've never encountered before so I'm scratching my head. I can only think that it's because...

What holographic material are you using? I've had some success with running it. I found that I have to keep sheet sizes small, the more reg marks the harder time it has. I've always had to use the yellow filter to get it to work and lowering the sensor sensitivity. That being said, I haven't...

I need to find a new one. Last tax season I left a note with two questions on it about expenses, never got an answer. Just recently I emailed them asking for guidance on buying a vehicle and the same thing, no response. These were not hard questions so I'm a little baffled why they couldn't just...

This is immediately what I thought when I saw this thread. Pantone is trying to get people into some sort of subscription service. Seems like a bad move IMO. What did Klaus Schwab say, in the future you will own nothing and be happy about it.

You need to calibrate you OPOS sensor to it and also a filter over the sensor helps. I've gotten it to work pretty good it can be picky reading the marks at times though.

So I started by just uninstalling Onyx 21.1. I noticed it had installed it to my removable drive, guess it defaulted there because of Onyx 19. Reinstalled to the C drive and performed the Graphtec update for 21.1. Did a test print and tried the roll and it worked this time after a few tries. It...

Guess this is just me in here now trying to answer my own questions. :p So I've tried Thrive 21.1 with the update and the roll barcode will not work at all. I talked with Onyx and they checked my settings and said if they had another update for the FC9000 they'd let me know. Well that's not...

Should be fine. I do a lot of "die cut" stickers on my D140 with the drag knife.

Also looking to know if there is a way to have the Cut Off function to happen after it finishes cutting one job? Might be a setting I have to turn off. I did a test of a couple roll barcode pieces, it read and cut the first job, then did the second barcode and cut, then it went back to to the...

I can get Roll bar codes to work but sheet barcodes don't seem to work correctly. it might be something I'm missing. It scans the barcode, say's it's retrieving data link information, processing, then it drops just below the start mark and starts looking to scan the registration mark. It can't...

Success last night. I was able to print and cut a roll barcode. There is hope! Don't see the need to spend $1k on a software update just to get my cutter to work with Onyx if I can help it. Going to try a few prints with barcodes today and see what happens.

This is typically what I do to build my smaller sheets I give to customers. For instance I've got to do 1000 - 1.5" rounds, I'll set up sheets of 25 with crop marks, save to PDF and Step them out in Onyx, run my printed material through the cutter and hand cut the sheets of 25up on a table to...

Looking for different ways to do sheet layouts in illustrator. Do the folks that do layout in illustrator, do you use a plug-in or do you manually step and repeat? I often do lots of smaller pieces, such as 1.5" rounds on sheets 8.5" x 11", I usually use a PDF with cuts and all and import into...

Yeah I've done the only patch they have for the FC9000 on my RIP version. It's definitely Onyx because the barcode works perfect through Cut Master. I just would rather not change half of my workflow I've got going. I'm going to try a trial of the updated version to see if it works, which it...

They had patch for Thrive 19.0.3 for Graphtec cutters. Are you talking about version 21.1?

That's not very reassuring. I put in a call with them today. haha

Yeah I might have to see if the issue is on the software end through them or machine setting itself. I'm waiting for Grimco to get back to me, not looking very promising. I'm not thrilled with the support so far.

Yeah I'm banging my head on this. I'm not sure it can be rotated with the sheet barcode because it's only on one side of the print. I'd hate to setup huge layouts in illustrator just to send to Onyx for the print and Cut Master for the cutting. Maybe I should've paid the $1k for the...