• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

marks

  1. Creasing when laminating

    Hi there. Cold matt laminating gloss self adhesive vinyl. Yes the lam and vinyl are compatible. Just started to get this :-( Wasn't a problem on laminating smaller sheets. This is by far the largest sheet size I have tried for quite some time. 2440mm x 1220mm. The creasers are all the worst in...
  2. How to offset crop marks in Onyx

    I'm trying to figure out if there is a way to offset crop marks in Onyx. I see how to set edge marks, but I need the marks to generate inside the bleed so I know where to trim.
  3. Need Help Graphtec FC8000 cutting unaccurately

    Graphtec FC8000 cutting unaccurately Does anyone know how I adjust my settings on my FC8000 I had it perfectly fine but I recently had my machine repaired from graphtec as the cutter was loose but now when I cut decals out using registration marks the decals had uneven sides.(See pics) The...
  4. CNC stud marks

    I'm looking for a better way to mark a routed sin face for studs. Currently, I'm changing our tool on the CNC router to a regular brush you'd find for a Dremel tool. It makes good marks so we can shoot studs later with the stud gun but over time (and usually on the same sin face) the brushes...
  5. Mimaki CJV30 Cutting Black Vinyl - With no Registered Marks?

    Hello, So I have a sign writing job to do with black vinyl. However is there a way to cut black vinyl on the mimaki Cjv30 machine without registered marks? I say without registered marks, because the registered marks are printed in black and will not show up on the black vinyl. Any help is...
  6. Onyx 12.1 and nesting files with cut paths and only one set of registration marks.

    Came across an issue to when a file has a contour cut and your have multiple files it will not allow you to use conserve media. Since the files have contour cut paths it will not auto rotate and causes issue. I called Onyx and they stated that this is true. If a file contains a cut path ti will...
  7. GX 500 won't find the last crop marks. HELP!

    Trying to do a large run of reverse printed static cling decals, print/cut. Printed on xj540 and trying to cut on gx500. We have done this job before with good results, but the plotter won't find the back set of crop marks this time. Only difference from the last time we did this job is we...
  8. CJV30-130 and Flexi 10 Can't seem to print, laminate, then contour

    Bought my Mimaki second hand and have been using it with Flexi 10. If I send a file and tell it to print and cut, it will print with registration marks, then read the marks and contour cut no problem. If I tell Flexi to print, pause, cut (so that I can laminate it) I can't seem to get it to...
  9. digitize point and x axis errors

    Anyone had digitize point errors where it is just looking in the wrong place for the registration mark? We've cut dozens of pieces in this job correctly but on this one sheet the head just wont read the marks correctly for some reason. We have made several of the same file and it read and cut...
  10. Onyx Thrive 12 and Fotoba XLD Marks

    Is there a way to remove the vertical fotoba marks in between copies of images? I only need the vertical line running down the side of the roll and not between each copy. I think I am missing something. Caldera does this a lot better unless there is a setting somewhere else I can't find.
  11. Kona 1400 not seeing registration marks

    we have a Mutoh 1324 and Kona 1400, running Onyx 10.5 I'm running a 49" x 75" print on 54" Arlon cast 9 year wrap, with the matching gloss laminate, that is to be contour cut. FYI - I have run lots of this type of job in the past without problems on the Mactac Gruv9 and Razor laminate products...
Top