• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Recent content by hottscennessey

  1. Hp Latex 110 - 17.3:11

    Has anyone run into this error? 17.3:11 Remedy:1. Check that the Main PCA to PrintMech black 1 cable is not damaged. 2. Check that the Main PCA to PrintMech black 1 cable is correctly connected to the Main PCA and the PrintMech PCA. 3. Replace the Main PCA to PrintMech black 1 cable. Can...

  2. Best adhesive to attach polycarbonate sheets to PVC fence

    Thanks for all the suggestions. I'll probably do some stainless through bolts, and fill the holes if I go in a different direction. I went with polycarb because it was the material I had on hand after a sneezegaurd job.

  3. Best adhesive to attach polycarbonate sheets to PVC fence

    Weaving it could be an option but I would like for it to go to the ground to keep the sand out. In the long term I'll have grass up to the fence in some places but in the short term it will be on the vacation rental market and I'm trying to keep the pool guy happy.

  4. Best adhesive to attach polycarbonate sheets to PVC fence

  5. Best adhesive to attach polycarbonate sheets to PVC fence

    Hey Everyone, I have a personal project where I'm trying to adhere .060 polycarb sheeting to a PVC slatted fence to keep debris out of the pool. Since it's a brand new fence I'd rather use an adhesive than hardware. I thought grimco banner tape would hold it at first thought but it failed the...

  6. fedex/ups fees question

    Icing on the cake is now in addition to the fees any ground package +48" is no longer guaranteed by it's commit date Sent from my SM-G955U using Tapatalk

  7. Need Help HP Latex problem with prints

    I have a 110 and it does not make that noise at idle. It makes that noise usually while it's preparing to print. Sent from my SM-G955U using Tapatalk

  8. 4over Banner Quality

    I've used 4over for banners and don't think the quality would be acceptable for 1-2 foot viewing. From 10ft absolutely, but there was still graininess from 3-4 feet from a vector text file.
  9.

    Non-corrugated Plastic Signage

    Thanks for the help!
  10.

    Non-corrugated Plastic Signage

    I have a customer looking for a .25" non-corrugated plastic sign with raised lettering similar to the one below. Can anyone recommend a vendor to produce this or somethign similar?
  11.

    9000s Banding After 10 Ft

    Thanks a lot guys. I'll inspect and replace, and of course report back. I really appreciate the picture of the dampers.
  12.

    9000s Banding After 10 Ft

    I see, do you happen to know if the damper is built into the print head on this model? I don't know where else it would be...
  13.

    9000s Banding After 10 Ft

    Replace even though it was recovered successfully? What is happening to the printhead internally that it would need to be replaced? What will raising the voltage do / compensate for? Thanks for the help, I'm still learning
  14.

    9000s Banding After 10 Ft

    Guys and Gals, I'm printing a banner that consists of mostly magenta, after about 9 feet the magenta started to band. I double checked the heater settings and they were all correct according to the manual. Afterwards I did an IQ Test Print and the banding was still there. About an hour later...

  15. HP 5500ps UV generic ink experience?

    I used the ink below and was happy with it. http://www.amazon.com/LD-Remanufactured-Replacement-HP-Yellow/dp/B002M3REPW/ref=sr_1_2?ie=UTF8&qid=1383093936&sr=8-2&keywords=hp+5500+uv+ink
See more
Top