Search results

We cut a lot of substance materials used to use a graphtec fc7000 it would cut in one go then a second cut to do the perf cut biggest problem was the general accuracy mainly due to the material does not like bending over the bed. Had the chance to buy a second hand flatbed graphtec all...

As said down to feed calibration. You can reduce the effect if you print and cut across the machines. And once you move away from standard materials the problem will show more. Or if you have to go in the feed direction then calibration for that material.. or at worse squeeze stretch the cut...

Have you completed a sensitivity test did it fail completely. Most problems I have with my graphtecs are cable connection related

What I liked about the older head system it was individual This way the suction unfortunately pulls on the least resistance I think you still have air in the pipe and a weak seal In the past I have always ended up with a headache after a chock clean so said I would never do another one and...

Been having similar till I found the cap was not sealing although all looked like it should. And the third new cap trying Carefully doing flush adjust etc. But at the moment if I connect the small side spring the seal fails. I keep looking at the mechanism to see what's worn or out of alignment.

Probably a speck of dirt on the feed encoder disk... of flat spot on the pinch rollers Could possibly be a fault in the Eps conversion but doubt it

When it goes for the back ones does it just stop and say marks not found or does it think it's found one and giggles about before it says not found On some of the older machines is a search limit it will travel the same distance each time but just stop at the limit and report mark not found...

Having been through all 3 myself with my still fabulous sc540 pro2 each change was a leap forward wasn't it . Quite happy with the max ink for now can't see a real reason to change. Thought roland were pushing to go to max3 missing out max2. And as you say where are the profiles not convinced...

As far as I am aware you should not put max 2 colours in the vs They always said oh max 2 white was not compatible until for some reason max1 stopped being produced.. then all of a sudden it's fine to mix them Since I upgraded ? To max 2 white basically nothing but trouble with the white...

I have a 7000 130 and the most troublesome plotter I have owned out of 7 I like the idea of the earth strap mine every now and again goes haywire when setting up lots of fiddling often a hour or so and it suddenly corrects itself.. last was reload the firmware instant cure but for how long ?? I...

Xerox 7800 is the nearest to your requirements as far as I know .. hi res 350 grm can add colour matching system.. Probably best on a page pack

Our corel to zerox had multiple page and colour problems from there drivers so we create a pdf from corel and print from acrobat through the zerox postscript driver. That works well and consistent. For the odd colour pick we chose from a pre printed cmyk chart The non postscript drivers...

Use illustrator or corel. Have some pre drawn cutting marks to import. 21 cards to a page Press print

I am with old paint on the driver i hate cutting master with a passion except if I have to cut something over 3mts in length

3 things come to mind Rip settings over riding machine presure setting or other way around . Need to find a spring guage to check the pressure is what it says. Grit in the actuator windings

Yes the graphtec should be set to do this on the outskirts side for normal weeding inside for reverse weeding but the fact you can notice the nick means something is wrong with your set up of the blade posibly it's just sticking out to far Is the normal cutting of good quality ? I don't think...

I was ready to buy dx4 sx cash in hand but worries about banding asked for test prints they looked superb but all only 80 mm deep wonder why.. except a a4 print cmyk that had poor banding. I asked for a4 prints of a couple of spot colours never got them so never bought Had a second roland...

As you said the cutting is done in the order you created them. Graphtec sort is looking for the nearest next loop start from the finished of the one being cut in the across direction. So will lead to unexpected results as it tries to reduce the feed back and forth For large cutting lengths use...

If it has the same function as a graphtec of front or rear loading. You have set the opposite way

Yes the main power cord As you say on set up the feed motor would go mad and bring on a motor error When checking the output of the power supply i noticed strange readings as the set up whent to move the vinyl then the feed motor would go bananas Would appear that there was voltage but when...