Search results

could be the same as my pro11 the limit of finding the marks are 3mts it will stop at that point and report crop mark not found.. press enter and it will cancel and return to origin....instead of pressing enter press pause (if i remember correctly) and it will continue its search..every now and...

i would be tempted to try and dismantle the head if you can get the cable out without damage then find a old head for the cable drying up in the mean time could be a problem only by the head from tried and trusted dealers yes they are ridiculously expensive

As said before other stuff is as good as. Cut to shape Mx laminate . Refletive material. Even the diamond grade.

I would move it all by hand to find the tight spot dirt or seizing head rail bearing. Think the xc is similar to my sc pro 2 so you need to switch off and lower the caps to free the head so you can move the head Has to be something quite drastic as it takes quite a bit of effort to separate the...

Sounds like the control box has been changed for a cheap generic type Show me a picture of it In the mean time check the bed temp with a temp gauge to find the real temp

I looked at this for a fc7000 130 not quite as easy as first look You need one from the same type of machine then you need to make it invisible to the set up firmware else it thinks it the outer roller. Two types of optical sensors don' know which for your machine. Bit of a tis to fit but should...

Thank you Enter +.7 in the scan value feed =0 press enter to save. Now when it prints and cuts it uses this new value. If you print this test again it will be exactly the same as it is now but the print and cut will use the values you set. This setting is only for print and immeiate cut. If...

Having read your post several times I think you are misunderstanding. The print and cut test with the scale will always show the amount it' out of alignment. You enter the discrepancy value. It will use this new value when it prints and cuts but if you do the print and cut scale it will still...

Confused is it a 540 pro11 or a 545ex If a sc540 where is the heater control box. If a 545 then heater control in the main menu. Also as I understand it if the no1 head is black then it can't be driven by the normal versaworks. There was a special dongled version. If the black head is no3 I...

Sorry not forgot you boys but its paper based and haven't found the time to scan it all. My Xerox should make a pdf of if if i press the right buttons See what I can do

It all happens at the design stage. It cuts in the order you drew it or introduced a object. You can change the order of a cut loop by moving it to the back cut first or front cut last on the drawing design. So if you are digitizing a logo you should draw in the direction you want to cut and the...

So what cutter were you using you will need to change your workflow but works well with a roland . Presume 20mil to be Mx type materials our fc 7000 did do it but not without problems Found a flat bed graphtec and all problems disappeared. The 7000 has since died but found a mk2 there really...

Sorry just read your last reply again if useing cb9 setup and cb15 blade all ok then probably a firmware fault just alter adjustments for good corners due to off set difference. I ave 3 graphtecs and odd things on them all. I have a flatbed graphtec for cutting substance the difference is worth it.

You are cutting at max pressure think 45 is max. I would reduce this a bit say 40 it will not make much difference to the cut. Also if like older ones there is a encoder strip in the head unit if this has a hair or grit on it then the depth of cut alters durrring the cut. Could also be the long...

Judging by the state of all the heads the capping and pumps are poor. Presume it's not Roland inks. The reason for the missing line could be seveal things. It will leave banding but not fading away print. You could change or swop the cable to see as its the cheapest to start with but to get the...

I have a hard copy don't think it was ever available in pdf. I will have a look but just think the page size has been reset Had mine from new used as a cutter only every day.

Pen up speed under the pen knife menu

Possibly need to set the handshaking to hardware. The data sent plotter speak is the same usb or serial it's just how it's delivered

I would have thought that problem to be media bunching or slippage from my experience of that type of material.

Normally this is the step size is mismatched between cutting master and the plotter settings