Search results

looks pretty similar to: http://www.identifont.com/list?2+nasa+2+BRD+1+BRC+2+2DV+8+BRB+16 (nasalization deluxe) , but not exactly...

I always ask them if the vehicle manufacturer is paying them to advertise their vehicles for them. When they respond no, it's usually an easy sell on removing them. The emblems with pins that go into holes always go back on, but regular VHB applied emblems stay off once removed. We use the thin...

Along those lines; not sure if you have an edge or not, but LexEdge II combined with a 2-sided adhesive (permanent/removeable) would be a possible solution for durable material that could be removed. Good luck with your project!

Sling Light

The thicker aggressive MacTac vinyls seem to stick to just about everything, not sure if this would be what you're looking for, none of the thicker vinyls I've used seem to be removable. Call Benji at Trigon Imaging (east side of Cincinnati) to see if he has any samples to shoot over to you to try.

Welcome from Florence, yall! Shoot me a link, I'd love to see if we can utilize some of your technologies to improve our offerings!

I haven't used phototex for a few years now (since my last job), but we printed on a Roland SP540 & had NO problems with scratching phototex. I did always install it with MacTac felt blocks though. We had one large job that went on the side of a box truck to advertise a yearly event. We put...

For posters I used Sihl papers here. It works great, and they have a variety of paper weights. Also, get a sample roll of the Sihl canvas when you talk to them.

I wrapped one once and laid heavy auto magnetic sheeting over those channels and wrapped over that, you could see the edges, but it didn't go into the dips & distort the edges. I saw it a year later and it was fine, but have not seen it since...

Can you quote it as hourly labor? With a maximum hour cap. If it comes in less time, then the difference is applied towards the new wrap.

Chalk it up as a lesson learned if a bill for your artwork time (no printing) does not get paid. In the future, start pricing your artwork time separately from the printing aspects, and/or insert a clause about the artwork time being reduced if the printing is produced by you. We do this for...

Can you save as a PDF from Illustrator & print from the resulting PDF? I try not to print directly from Illustrator, but I do not have a setup anything remotely close to yours. The dot pattern looks like a standard 4-color process pattern, adding the dots to make up the final color (100%...

Check your bank's policy on insurance company checks - most hold checks from them for 10 business days, for this reason...

We recently learned that we can print on canvas material on our solvent printer, we've gotten a lot of interest just from other employees here, so we ordered a roll to try it out. The prints look GREAT, however we do not have current supplier for the frames that you stretch it onto. We've looked...

Cleaning the eye is very important, as it cannot read a clean strip if it has a little piece of lint on it. Hopefully you're good from here. Also, a few drops of 3-in-one or sewing machine oil on the carriage rollers/bearings (work it back and forth and wipe off the junk that comes out) will...

Neil Bold & Loft Mammoth are the closest I could find, but neither are correct...

well, thanks all. I'm still not sure I have a correct answer... :banghead::banghead:

We're off the beaten path, down a dead end road so signage only helps people determine that they're at the right building. If you have BNI in your area look into it, I receive about 90% of my business through it either directly or indirectly, excluding emergency vehicle work.

That makes it 100X easier to install. Just always be sure to go over all of the edges of the laminate to be sure it is seated down, then hit it with the torch or heat gun to set it.

So, this file attached, completely created from scratch, based upon what the customer gave me as a "sketch", is sufficiently legal to print? (it did take 20 whole minutes...)