Search results

With those Roand's (and Mimaki's too), it's always more efficient to have prints lined up in the scan direction first (head travel direction), before adding more copies in the feed direction (table travel direction).

I found my answer, and the answer is no.

ha, after that post, it quit again in February and I stopped using it at all until a month ago. Now it seems to be kind of working again, but I haven't had time to deal with it much. We found a dealer kind of close that's willing to help, but we basically have to prove to him that it's a piece...

we've had ours since summer of 2018. We ran into a banding issue in 2023, and they replaced the heads for like $3500 within a few days. That's the ONLY real issue we've ever had. It's been such a great printer that we bought a second one in July as a backup because it was discounted so much...

Is it possible in Onyx Thrive to create a quickset so it outputs the barcode marks on the sides of the roll instead of top/bottom, and only prints a maximum length? I want to use OPOS or something on our S2 to cut certain files, but would need to keep the maximum length of the roll at 30" to...

About 5 seconds before you're ready to hit print. Although mine has gotten better about not doing that to me.

I don't think you can adjust it without digging into the service menu/program. It cleans often enough to keep working well, but not so often that it wastes a bunch of ink if that's a concern to you.

I literally just ordered one this morning, $17k thanks to an instant Epson rebate. Retail is $25k, but they've been down to $17k for the last 3 or 4 months, not sure if they'll stay that low.

nothing wrong with getting the small bottles...when they're available. Some colors I struggle to find the small bottles, especially Lc&Lm, so those usually end up being the big bottles with everything else the small bottles.

I'm looking to find a good printer/process for printing very small runs ( probably less than 250/month) of high-end custom packaging, mostly sleeves but other styles as well. I do not care one bit about speed, I need the absolute highest print quality possible, especially in greys. It would...

hopefully I have it fixed, there was air in the dampers. Crappy design to have both dampers for white connected together.

Does anyone have a good site to order parts in the US for LEF2-300 printers? Ours is having an intermittent loss of white and we haven't been able to get decent service for months so I'm going to start throwing parts at it if I can find a place to order them.

we'll give it a shot. I still need a service manual and better parts supplier if anyone has one. We don't have time to wait for our tech when they don't reply to emails for days at a time.

no, they haven't tried that. I don't think we've got that many cleaning cartridges here at the moment.

Anyone have a good place in the US to order parts for an Lef2-300? And a service manual as well? Our tech hasn't been very responsive over the last 6 months or so, and I'd like to just fix the thing myself. We've been getting no white for days at a time, then it'll work for a day or two and...

where'd you get it from?

I've been trying to fix an issue with one of our 6042mkii printers. The table isn't level with the carriage from left to right, by a good 1.5-2mm. Checking with a bubble level, I can get the table level in both directions, but then the rail the carriage rides on is out of level (by a lot). If...

did you make sure to check the level of the printer itself? I had that cause a similar issue not too long ago.

Everything looks fine. I replaced the rubber and cleaned everything, but it still sits at that angle. I'm ordering a new cap assembly to see if that fixes it.

Does anyone know a way to adjust the angle the cap stations are sitting when contacting the heads? I can't find anything in the service manual about it, and it's causing ink to leak out the side of the caps. I've checked the station height and that seems fine all around. They sit flat when...