• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. JFX200 Issue - I'm Stumped!

    When you tricked the machine did the error on channel 8 move another channel?
  3.

    CJV30-160 problems with head

    When is the last time you replaced your dampers?

  4. Question Parameter Mimaki Cjv30 160 ink ss21

    Send your dealer or Mimaki an email with your serial number and they will provide you with the file. Mimakiservice@mimakiusa.com Mimakiservice@mimaki.com

  5. Need Help JV33 Print Head error

    Check the head cables and I would load the original parameters if you have them.

  6. Jv 33 printhead cables

    Vander is correct they can be bent. Or you can just buy the ones that are pre-bent. I always use pre-bent. But, Mimaki is located 5min from where I work so 100% of my parts come from there. Lol

  7. Jv 33 printhead cables

    They should come with the bends in them already. Have you tried installing them already? If so are they long enough to reach the board?

  8. Jv 33 printhead cables

    Part number E104933 Item 13 in the attachment?

  9. Jv 33 printhead cables

    Did you get the cables from Mimaki?

  10. Considering Mimaki JV150-160 - test prints needed

    I can help you with some test prints. Send me the file via email Louis.darby@reecesupply.net Www.reecesupply.com

  11. Considering Mimaki JV150-160 - test prints needed

    Where are you located?

  12. Suggestions Mimaki JV33 error

    I agree it’s probably the head FFC cable.

  13. Need Help JFX200 error code - SYSTEM HALT SLRY-F5

    Normally the warranty on a JFX200 is for the first year only. Unless there is a dealer promo or you purchase an extended warranty plan. Just an FYI the fuses on JFX200 boards are not the snap in and snap out kind. They are soldered to the board.
  14.

    Need Help JFX200 streaks

    Do you have a picture of the Nozzle test print? I would take a look at that first. Also, you may want to check your Head Voltage via #Adjust and make sure your encoder strip is clean with no visable damage or scrapes.

  15. Looking for pinch roller to FC7000-75

    Www.reecesupply.com

  16. Laminate Help Needed

    Buy a Laminator! Royal Sovereign sells a 55in for about 5k brand new or you could possibly get a better deal through a dealer.

  17. CG-130SRIII pressure issues

    Have you tried replacing the Blade holder? I had a customer with the same issue, we replaced the blade holder and it fixed the problem. When we took the old one out and shook it a bit the blade popped out. Worth a try if it’s covered under warranty.
  18. L.D

    678-431-4955 Email: Louis.darby@reecesupply.net or LouisDarby22@icloud.com

    678-431-4955 Email: Louis.darby@reecesupply.net or LouisDarby22@icloud.com
    • L.D
    • Profile post comment
  19. L.D

    Reece Supply Co.Ga

    Reece Supply Co.Ga
    • L.D
    • Profile post comment

  20. Mimaki JFX200 error code

    Have you updated your firmware?

  21. Mimaki jv150-160 1bc halt system

    I thought you said you had readings of 13.8kOhms?? Those went away and now they are 17.0kOhms? If you just had a new print head put in and have had this error ever since; then the problem is probably with the print head or installation error. I don't understand what this means? "The printhead...
Top