firmware

Our HP 360 Latex printer will not let us upgrade the firmware. We have tried for over a year to make it work. Here is what we have done: 1.) Use the printer interface. It says new firmware is available, and it downloads the new firmware, then we get the error "The firmware package update is...

Hi All! First of all, I appreciate the advices provided for my first post, they were very welcomed and useful. Now, I need to access MSA to install firmware (through Board wizard) and have seen that the only way is to get access via technician. I am looking for someone that might grant me 1...

Hi! Nice reaching y'all from South America. I am taking charge of my father's company (so am very new to all this) and we are looking to do a facelift of printers, which some were in bad shape. We have a Mutoh VJ1624 out of service about a year ago, so we bought new boards and printhead from...

So, yesterday I changed out a liner encoder strip on our Roland SP-540v (firmware 6.3) and, although it prints the image still "skews". I figured I'd need to do the "Linear Encoder Setup" as per the Service manual. I attempted AS I HAVE DONE IN THE PAST to enter service mode... the usual, start...

Hello, Have a L28500 that are still running but need to upgrade to a later firmware. Unfortunately I have been lazy on upgrades since I bought it in 2013 so I am running on an old one BM_07_00_00.4 I have through my local HP technician been able to get hold of BM_10_00_00.2 as the next, but the...

Hi. I'm new to this forum and wished I had discovered you all years ago. I just had a repair tech replace my Epson 7890 main board. I thought all was fine but when I tried to switch the black ink the printer went into an endless loop and never completed the task. I had to force the printer off...

Hello, My name is Ben I have been printing with my xc-540 for about ten years so I know the machine very well. I recently had my network card fail on my machine, and unfortunately, it is part of the motherboard. Luckily I was able to get a backup of the motherboard parameters and latest firmware...

It's so odd. I pass everything in the connectivity test, except verifying the time/date. Any suggestions why? FYI, I do have a VERY old firmware. Not sure if this is an issue. Don't ask me to update the firmware. I can't jump from a very old firmware to the most current. Anyway here is...

I am connected to the internet. I have tried updating the firmware manually and through the printers screen. I just can't seem to update my HP Latex 360 to the latest firmware update which is NEXUS_01_14_00.5 I have version NEXUS_00_06_02.10 installed currently. I get "The Firmware update...

I am connected to the internet. I have tried updating the firmware manually and through the printers screen. I just can't seem to update my HP Latex 360 to the latest firmware update which is NEXUS_01_14_00.5 I have version NEXUS_00_06_02.10 installed currently. Do you think it is because I...

My JV3-160SP Main Board finally crapped out. I replaced it with a new one, however, the new main board has a different firmware. The new main board has the firmware: JV3-250SP v7.10 / MRL-II2 When I boot up the printer I get the following message: "Confirm AMF" My JV3-160SP does not have a AMF...

Currently firmware version 5.0.0.8 is on my L25500. The latest version for download is GG-CAL_07_00_01.5 ..but that won't load on the machine. There was a version 6.0.1.6 that is no longer available for download. (anyone have that by chance?) So, now I need to figure out how to get that...

Hi! Our JV3 160 SP II recently had the main board burn out. I purchased a used replacement, however it turns out that it used to be for a 250 SP. Also, the v.7.00 firmware doesn't seem to recognize our CISS. Would someone be willing to share the v3 firmware to flash it back to a 160 SP II...

Through an unfortunate series of events we wound up with firmware for a FB750 on our FB700. Our hard drive failed, and we were told by HP that the new part number for the 750 should work for the 700. It doesn't. Is there an easy way to rollback the firmware? I tried sending a previous version...

Guys, Need some help! I`m trying to install a new motherboard on my mutoh RJ900-x and when i log on MSA i keep getting this mensage. Imgur: The most awesome images on the Internet And when i click on ''ok'' it come as printer unknown with no options to update the main firmware...

Guys, Need some help! I`m trying to install a new motherboard on my mutoh RJ900-x and when i log on MSA i keep getting this mensage. Imgur: The most awesome images on the Internet And when i click on ''ok'' it come as printer unknown with no options to update the main firmware...

Can anyone tell me the current firmware version for the 3042? My printer says 3.40. If this is not the current version can anyone tell me how to update it? I'm having troubles getting this Kebab installed & I'm hoping this is the problem.

Can anyone tell me the current firmware version for the 3042? My printer says 3.40. If this is not the current version can anyone tell me how to update it? I'm having troubles getting this Kebab installed & I'm hoping this is the problem.

Dear Members, I just bought a used CG130 FX and I'd like to upgrade the fw. I have 2.4 fw And I would be happy if somebody could send me a maintenance manual and mechanical drawing as well. Thanks a lot!

I've seen forum posts in the past on the Error 16 issue but haven't seen any resolutions. Has anyone heard of any good fixes for this issue, or a through understanding of the actual error code? Been struggling with sporadic intermittent error 16 issues for a little while now. I'll get like 98%...