• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1.

    Roland sp-300 looking for printing help.

    When the heads are running better, do a Bias test and set that up. Then do a bidirectional and then a feed calibration
  3.

    Roland sp-300 looking for printing help.

    https://downloadcenter.rolanddg.com/contents/manuals/SP-300_USE_EN_R4.pdf This has some that may help
  4.

    Roland sp-300 looking for printing help.

    You need to spend more time cleaning the heads and only then do a complete calibration. Too many missing nozzles causing the banding.
  5.

    Roland sp-300 looking for printing help.

    Do your test in versaworks, alternatively go into the service mode menu, arrow down to test print, enter, arrow down to fill and print that pattern. Also a nozzle test print would be handy to verify the heads are ok.

  6. Don't understand.............................................................................. ? ?

    I hit ignore on a couple of them yesterday and it totally cleaned up my page. It was getting bad. You also need to hit refresh after each ignore, to see if there are any others you missed.

  7. Need Help Connecting a Roland Sp540v to computer/VersaWorks

    Download InterCon Nettool to first read what the IP address of the printer is. Note, you require a crossover ethernet cable to run a SP540v. The 540 doesn't actively show the IP address in the printer menu.
  8.

    Mimaki JFX200-2513 Printer is missing entire yellow color

    Ensure the ink cartridge solenoid is operating, and if not, just jam it open until you get another.

  9. Source For DX4 Printheads?

    https://www.sign-in-china.com/products/2132/original_and_100_new_roland_dx4_eco_solvent_printhead_6000005213.html

  10. My print keeps coming out about 1/2 in too long????

    Section 2-14 of this one https://mimaki.com/archives/034/202211/D202681-35_JV300_OperationManual_e.pdf

  11. My print keeps coming out about 1/2 in too long????

    Need to calibrate regularly, either changing rolls, changing width or types of media...The tech would have only calibrated it for the media that was in the printer when they were setting the calibration.

  12. My print keeps coming out about 1/2 in too long????

    Chapter 3 https://mimaki.com/archives/034/D202740-13_JV300A_OperationManual.pdf

  13. VS 540 Printhead Replacement Question

    The head number is only for service records..

  14. JV300 Strange colour drop out issue

    Replace dampers before anything else...
  15.

    Roland Versercamm SP540i - Banding and nozzle issues

    Your pump lines also look to be blocked or your pumps has failed.

  16. roland sp300v no ink

    Presuming your captops are in good condition, run a couple of cleaning cycles, then try another test print. If no print, you will need to check the two fuses for the heads, on the main board.

  17. Mutoh 1204 printed 48 hours ago and today nothing

    Dampers all full and ink at the head?? Check fuses next to transistor heatsink on main board.

  18. Roland vp540 repair

    How do you come up with 7-8k?? Search 32437257839 in aliexpress

  19. Roland vp540 repair

    All consumable parts are available for those printers. Discontinued indicates they don't make it as a model now.

  20. Seeking Assistance for Roland VS 540 Linear Encoder

    Recheck your encoder strip and make sure the clamp and spring are not bottoming out. They sometimes look tight but are not fully floating between ends.

  21. Roll stopped rotating, printed in same spot. Now not printing at all

    Your local electronics shops should be able to supply them...As a test, swap them around..
Top