blade

Hello folks I had my original Roland Cutting Plotter, somehow they broke and found this one almost same as mine - https://aliexpress.com/e/_DDxfJ1T Since I dont like to buy on aliexpress before I buy it just want to hear your exp... thanks folks!

Hello all good people, as the title say I want to buy Graphtec cutting plotter knife blade holder and found this one on aliexpress - https://aliexpress.com/e/_DmSrmBR What do you think about price and quality? Its my first time buying this so any help is wellcome, thanks!

We have an old but very great Roland SolJet XC-540. There's a spot on the printer about about 12" in. Whenever the carriage passes over this spot, the blade toggles up and down a couple times. It isn't dragging over the print or messing up the ink while printing, but it goes up and down, so...

Note: Sorry for the bad quality photo, it's the only one I could find of the cutter and it was sitting in the background, so I had to crop everything else out and zoom in on the cutter. Does anyone remember this cutter? I believe it was called a "linear cutter" or "linear slicer" The first...

I think my old age is getting me now. We have a S2 t-160 series cutter and the blade we have been using needs changing. I see where Airmark recommends a 45° blade as standard, a 36° for reflective and a 60° for sandblast medias. I was under the impression a 36° would be the best for universal...

we've been replacing cut blades at an alarming rate on our roland truevis vg-540. at first i thought it was due to too much pressure when cutting, but after replacing the strip, the blade, and dialing back the pressure, realized something else is breaking the blades. took a close look at the...

Hey all! We are currently working with our go-to tech guy, but this issue is a pretty big mystery with a lot of back and forth, so I'm just throwing it on here in case any of you have experienced this before. Our Roland 54 no longer cuts consistently from day to day and even job to job. Here's...

My plotter came with the Blue blade holder and the CB09UB blade. I Often use the perf cut feature and have read it would be better to purchase the Red blade holder and some of the CB15UA blades and swap them out when i go to do the purf cut. Does anyone have any experience with the red over...

Hey Guys so i ordered some concept 235 (4mil) & 238 over lam (12mil), now i have problems cutting when i feed it back in after lamination. Doesn't seem to cut deep enough? Is there something i maybe doing wrong or maybe the blade I'm using is not right? (60 degree Roland) Any help would be much...

We have been fighting this problem for over a year. We can send 20 jobs and everything is fine. Then suddenly in the middle of a job the blade gets "stuck" in the down position. If you grab it you can lift it up fairly easily, however when you let go it goes right back down. Case in point...

I need some help. I've had this plotter for several years without any problems. I tried to plot with it and it asks for type of media (ie:Roll, sheet) so I pick either one and the blade carriage moves slowly to the far left then hits the end and gives me "ERROR E01019" message. I've installed...

Would anyone know where to get the cutting blades for a mutoh ultima SC-1400D? They have the small stop on the end that a lot of them do not have. We are needing the 60 degree blades for the thick material that we cut. I can always find them on Ebay but they are out of the US. I used to have a...

Hi guys, We have some jobs that require small text to be plotted and we have been using the CB09UA blade. This is fine but I noticed the smaller text the harder it is to cut cleanly - the joins are not complete and in some places it doesn't cut through the media all the way so we have to finish...

Hello Folks, Just wondering if it is possible to print and cut on a soljet pro4 xr 640 a simple 7" triangular decal?? I am having a hell of a time getting clean cuts. I have replaced the current blade with a new 60 degree blade, change the offset to .25 and still no luck. I'm running orajet...

I produce small stickers. After a couple years I have ironed out most bugs, but weeding continues to be unpredictable and painfully frustrating. For a few months - no issues, then it all of the sudden starts weeding horrible. I use a 3m vinyl with Avery 1460 lam with a d60 summa plotter. I have...

Hi Folks, I'm running a tjet1671c. My 'current' prob is that it starts a cut fine but as time goess on the cut runs off. i'm cutting out motox / quad decals. 1.5m x 1.5m. If I use 2 or 3 cuts, after the first cut, the 2nd cut is say 5mm on the x and y axis off. i had thought it was initially...

I'm hoping the community here can weigh in on this for me as I keep getting different answers from different places. Originally, we were using a 45 degree blade on our Roland Sp-540V. But as our small lettering kept tearing, someone recommended switching to a 60 degree blade for fine detail...

We recently started cutting 2mil cast vinyl for one color designs, instead of wasting ink printing. Last week, we had to change the 60 degree blade as it had become severely dull (we thought the blade would last longer than 2 months, but we have been cutting 6mil vinyl a lot so perhaps that...

I have a Master Plotter XY300P. Been using it for quite a while, (bought it way back) on and off. I finally need blades. Does anyone know what brand is compatible with this plotter? Where is a good source for blades?

Looking for recommendations on a flatbed printer for styrene. What are my cutting options - laser, blade, router? Would appreciate your feedback if you have one and how they perform. Thanks.