rasterlink

I need some help guys. I am having issues with my Mimaki CJV30-160. They are as follows: 1) Black turns different colors depending upon the color printed next to it. For example: black turn slightly green when printed in the middle of a green field, the same goes for blues (black turns blue)...

I have been noticing recently on our prints that we have been losing anywhere from 1/8" to 1/4" on prints over 96" through the printer (feed direction). The scan direction size has been off by 1/16th to 1/8" at most . It hasn't been a huge problem till now since alot of our prints are created...

Good day all, We just got a windows 8 machine to replace an old XP PC that runs our RIP and Estimate software. I'm running Rasterlink Pro 3 on the XP machine for our JV33-160. Our supply vendor (Grimco) suggested that I should reach out to the sign community and see if there is anyone not using...

I've run in to a significant issue when printing with one of our Mimaki UJF-6042: Our "special color" is being offset from the primer and color layers that are being printed (example of print below, with abnormal prints highlighted in yellow ellipse). The white layer is offset by roughly 0.02...

Today I went to start up rasterlink pro5 as usual, but the loading screen is stuck on "Checking profile information of JV3-160 SP". Has anyone else ran into this issue?

We've been working a summa plotter S160 with CorelDraw X5 for sometime now, and we have now come to upgrading our Corel software to X6. I have downloaded the new winplot plugin for X6, so that OPOS markers can be automatically added to a piece of artwork. When I click on the OPOS marker button...

Hello. Two days after my Mimaki JV33-160 printer was installed, my computer crashed and unfortunately I did not have a recent backup with all the Rasterlink software, drivers and profiles installed so I ended up reinstalling everything myself. I have everything working again but now when I open...

I have color managed my Rolands with Versaworks using our XRite I1 Profiler successfully, but we have now sold one and got a Mimaki JV-33 130 and ES3 ecosol ink with bundled Rasterlink Pro5SG. I like the printer, don't like Rasterlink. I have had a hard enough time learning this clunky RIP and...

Very infrequently, I'll feed a PDF into Rasterlink(v5) and instead of RIPing the PDF normally, I'll get a blank white image. The dimensions are correct, there's just nothing but whitespace where the image is supposed to be. I've had this happen on two different computers that are hooked up to...

I recently had a large order in which I had a number of sheets that had to be printed exactly to size for an outside fabricator. I noticed that everything I was printing was coming out around an inch short on the vertical drop and couldn't figure out why. My files would be the correct size in...

Hi folks, I've been running the program for years without a snag but it suddenley froze up while loading. I've been trying to do a fresh install for a few days now. Running WinXP 32bit, initial install goes fine, but when I attempt to run "Printer Management" the program freezes while trying to...

Bought a used Mimaki JV3 160 SP and got my hands on this version of their RIP software. It came with minimal profiles and was wondering if anyone had any profiles they would be willing to share? The vinyl manufacture sites only seem to have ICC profiles and for this old version of the...

Hi. I've been searching around here for a few days looking for some help on the existing threads to no avail. A few days ago the tower that runs our Mimaki (JV33-160) totally crashed on us. We just got a new one in yesterday and I've reinstalled our RasterLink Pro III software. My problem is...

Hello From sunny Puerto Rico, I have a MIMAKI JV3 75SP AND is having problems with the Fire wire board. How can i make the RASTERLINK SOFTWARE WORK WITH THE JV3 PARALLEL PORT? THE SOFTWARE IS ASKING TO AD THE PRINTER, BUT I DON'T KNOW HOW. Thanks in advance for your help!!!! Wilfredo Nieves...