• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

cjv30

  1. CJV30-160 DX5 printhead replacement question, please help!

    I have a cjv30-160, and the right black channel is FUBAR. I'm going to replace the head with an original mimaki p/n m007947. Do I need to replace the memory PCB as well? can I reuse the original one? I've read conflicting stories on this, and need to know before I buy a printhead. Any help is...
  2. CJV30-60 Printing failure

    Hello everyone. I need help. I bought a Mimaki CJV30-60 used. But it prints using Illustrator CS3 with FineCut 7.5 and the Rasterlink 5SG. The print will have a failure, as in the photo. I have not found how to fix it Was made several cleanings Has as leave the machine in adjusting the LCD factory?
  3. Mimaki JV33/CJV30 Epson Printhead dx5

    Hello! i bought a decoder board for DX5 printheads, can anyone tell me which is the P/N of the Epson DX5 that works on a Mimaki JV33? I specify that i need the solvent one. Thank you very much!
  4. [ CJV30] Print > Laminate > Cut ??

    Hello everyone, I need a little bit of help. Basically what I'm trying to do is print some stickers using the CJV30, then laminate them with my laminator, then after they have been laminated put them through the CJV30 for it to cut. I have just tried to print one sticker (it has the registered...
  5. CJV30-100 Mainboard parameters

    Hi everybody Can someone give me the way to initiate a new cjv30-100 main board. the farmer is dead. I just replace it today but i don't have the old data.. The printer start as a cjv30-60 in spanich... I have firmware update tool- I think i need values for/from a cjv30-100 ss21 printer...
  6. Capping Station and Head Pressure CJV30

    I seem to have lost the pressure between my head and my capping station. Each time I try to suck under the capping station, there is no pressure or suction at all, now my printer has stopped printing completely, should this be happening?
  7. Error 43 - CJV30 - 160BS

    Hi all, A few weeks ago I started to have the error 43, i was reading this forum and others that could be the Motro Y, I contact the technical service and they told me the same thing, so I bought the Motor, after changing the default Motor, the problem persists,I clean the encoder also, I...
  8. Mimaki cjv30 series printer opinions wanted

    I am about to purchase a mimaki cjv30-160 printer cutter. I would love to hear the good and the bad from anyone with experience with this machine. I am also trying to decide between the 4 color, 6 color or possibly 8 color with white and metallic so any opinions about the ink options would be...
  9. 3M profile needed for CJV30 ES3's

    Hello All, I am in need of a 3M-IJ10 white vinyl profile. I am running ES3's - 6 color (C,M,Y,K lc,lm). I looked on the 3M website and they didnt show anything for ES3's. I have some ES3 profiles for 6 color if anyone is interested. I just really need one for the IJ10. Thanks
  10. CJV30 Firmware Downgrade Help Needed.

    Hi everyone, I installed a third party bulk ink system on a Mimaki CJV30 but it can´t recognize the new permanent chips. I´ve been told that the problem is the Firmware of the printer, actually it has the 2.3 version (the latest) and I need to dwongrade it to de 2.2 version. I have the 2.2 rom...
  11. problem printing test -CJV30 160-

    Hi, You will find attached the test print, please help me to solve this problem.
  12. cjv30-130 (x Overcurrent:ave)

    My cjv30 had a majour issues recently and the mian board had to be replaced after 2yrs of use :( since then I have had this error (x Overcurrent:ave) when mainly cutting media. Has any one else had this issue. I have ad the enginner out today as well and he has stuck teflon tape all over the...
Top