jv33

Hi, Today I finally replaced the print head cap on my JV33 and printed a job after months of inaction... after ten minutes of printing the machine beeped 3 times, display screen was blank, but power light still on... the raster link status displayed a message stating the print job had been...

Hi! Im completly new in LFP, after preparing a used JV33-260 (new printinghead, new ink), I run into troubles after adjusting the head. Printing with RasterLink is working, but printing in bidirectonal mode causes ghosting - a difference between the two ways about one millimeter. (see...

Hi, I've just purchased a few of new DX5 printheads to replace. It turns out that on the print, there would be an annoying line at 60cm. I heard from people that Epson are trying to do something to eliminate of other manufactures making use of their DX5 printheads? I'm in desperate need of...

Good day to all. I have been trying to get everything sorted out in my head regarding the Epson heads used in my Mimaki JV-5 printer. The Mimaki part # is M007947 and is stupid in price. Some suggestion has been that you can use the JV33 head without the 'board' and transfer the one off the old...

Hello, I have been messing around with my New Mimaki JV33, and see these weird ovals on my prints. Only does it where the Cyan is right now, but for the life of me can't figure out where. Done some cleanings, but I'm new to this so maybe I'm missing something? Is it maybe the media...

I recently had a large order in which I had a number of sheets that had to be printed exactly to size for an outside fabricator. I noticed that everything I was printing was coming out around an inch short on the vertical drop and couldn't figure out why. My files would be the correct size in...

So in our JV33 160 something went haywire and fried out main board about 2 months ago. We took it out. Sent it for repairs. Got it back and re-installed it and everything went peaches and cream until 2 weeks later the same thing happened! AGAIN! but this time, it was worst. Main board couldn't...

Hi. I searched through lots of threads but couldn't seem to find the information I am looking for. I'm still fairly new on here so maybe I am looking in the wrong places. Essentially my problem is this. Most of our prints look great but when needing fine detail, particular small text, it...

HI All, Just thought I'd share this info for anyone with any printers that use DX5 heads, the info was posted to the jv3 yahoo group mailing list I don't have a DX5 series printhead printer, but this is worth sharing Ha! On JV33 and other machines that use a DX5 head - it has quietly become...

hello im new to the forum i run 2 mimaki jv33 for sublimation printing. recently i noticed about 15 random spaces in my number 7 blue channel on the testdraw ,ive cleaned and several nozzlewashes also ive flushed this channel with a syringe & cleaning solution but still the same 15 blank spaces...

Good Morning All, This is my first post, been lurking for a while now. I have a JV33 with a Colorburst v9.4.6 demo and I'm trying to run 6C+white ink through it. So far, unsuccessfully. Just got off the phone with Colorburst and was told they don't support that inkset, which I believe based...

:banghead:So I'm printing like any regular day, the machine finishes the print and all of the sudden a steady BEEP goes off. No messages or nothing. The control panel is frozen so I turn the machine off, waited and turned it back on and everything was fine. Later on went to do a cleaning and...

Hi I attempted to run a discharge and wash on my JV33 as I have been having trouble with ink not passing through to the heads. Ended up wasting the ink in the lines that were making it through the heads, while the ones with blockages did not drain at all. To top this off I did not realise I...

One of my vendors sent my ss2 instead of ss21 inks for my JV33 Is there a huge difference Can I use them, change the chips etc. If I do use them will it affect my warranty Thanks in advance

Hi, I have recently bought a Mimaki JV33 with the aim of printing short runs of stickers and labels. I use ES3 inks and a roll of Ritrama RiJet vinyl which was supplied with the printer, and use an ES3 GPVC profile from Mimaki. I am quite happy with the print quality however areas of single...