Search results

my advise would be do not buy on sales speak go and try it your self first...its an acquired taste and you must have a market for it

if its any help i use the roland and versaworks the rip has a swatch of metalic colours so you just select the spot colour, all well and good if your rip does that but if you have to mix it your self some ideas. as i understand it the silver is not printed as a underlay or over (like you would...

had exactly the same in the uk but only the metallics 751 silver gray gold the higher up the side the worse it was bonnet and boot disasters, had more luck talking to the garage door than oracal, the thing i put it down to was very poor UV resistance (uk weather remember not Florida) some of it...

why change the damper so soon after changing the head, presume std inks as a rule if changing the head renew all bits that touch it at the same time. think you may have answered it at the end, all the cleanings in the world will not help if the cap top is not sealing, around 12mth change on a...

thanks for your time any more views from users.

i am interested in your experiences with roland white ink. we have been using a vs 540 with white+ met for around 7 years and still have the pain of maintenance of the white ink, the silver has never been a problem. the first white ink was at best just adequate and required reasonable...

the fault is across the bottom right corner 4 colours involved even the black is going across which is normally a cap top issue or pump. is there a re-circulation pump on that channel ? where it would have been a silver and what is the eighth colour

far too much cross contamination mostly at the front right edge unfortunately several possibilities. as you said you have pushed ink from the top internal seals of the head may have failed. poor pump scavenging, dampers not sealing not uncommon for the old o ring to stay on the head or internal...

cap top adjustment is called Flushing adjustment this sets the left right seating when sealed

been through the same with my sc540 pro2 after a lot of mucking about concluded the silicone ones have got too sticky back to original all ok... for a short period better to run without the scraper than it keep stalling. if you want to the wiper mech comes out in one bit so you can check and...

just a few things to help you on your way the carts are colour slot sensitive by the small bumps sticking out of the case different arrangement for each colour. the cart physically wont fit in the wrong slot. you may be able to file them off but never tried, and of cause you need 12 of them, i...

if you have tried the chinese ones then ok we found them fine for the mx materials and perf cutting and anything we have thrown at it so far. we bought it used for the mx materials and not looked back, just had a look at the old jx and very similar to the 2250 the jx manual only shows part no...

can tell you the ebay blade holders are fine both the 09 and 015 and cheap enough to have several with different blades in. shame about the coil was hoping same as some other machine not 7000 or 8000 found some encad parts more available than graphtec for my old jx ... i have a 2250 as well so...

Because the colours are intermittent I would guess air still in the pipes. Try not to do power cleans very heavy on ink and pump life. The test prints look like on banner material giving odd look. Double check the seating of the dampers and pipes for air leaks but really the tech that fitted it...

customer is always right .........till they get out of the door.

just before you print do a sheet cut off on the printer that will give you a straight edge that will be in alignment to the print, align this edge with the cutter bed lower the rollers, then your normal set ups. you may waste 2 3 ins of material but guaranteed to be in alignment to the print...

Ok see it better on my phone. Still seems like a lot of movement. Does the cross cutter work ok. As this holds the knife higher. The thing they had you do was a possibility but surprised they did not suggest the main ribbon flat cable or to reseat it. Also double check in the settings that the...

i can't see very well but the blade holder does not appear to be located fully down in the block ( its slipped up) this i think will make this noise cos the pen holder is slamming against the bottom of the block unit just luck that the vinyl is being cut by having to much blade showing.

I was able to draw ink into the dampers but none at all past that point. Syringed waste tube coming out of the pump, nothing. Syringed lines between cap tops and pumps, nothing. Cap tops are still dry. sounds like the cap tops are not sealing if you connect a syringe directly to the cap top...

my guess would be the blade is not being rotated to the correct angle making the blade scrape across the vinyl and judder. posibly caused by a faulty head cable or main ribbon cable have you got the drag knife assembly to try.