Search results

This machine has less than 5 hrs on new print heads. We lost our biggest client a year ago and have hardly used the printer since. Operates perfect, comes with a laptop and versacamm software, mostly full 440 inks, a good amount of media, manuals etc etc....The printer originally came from bay...

Hey guys, need a hand. My feed setting is far off, (see image)...Making all adjustments under print/cut alignment does nothing...I have cleaned encoder, tried all ideas in manual, it seems to make no effect on correcting cut...any ideas? PS, as you can see in the image, the scan setting is...

I lost my yellow...Upon cleaning in service mode I am seeing a stream of bubbles being sucked in to the damper from the ink side...- Do you think a damper replacement and a new o-ring will fix? joe

has anyone replaced this on a roland sp300v or comparable printer? I have ordered one but on the senor map chart it looks just like the the encoder sensor in terms of location...There is no "limit sensor" on the sensor map in the roland service guide...please help - joe

after 1 month of not printing, new heads, new fuses...got the thing printing...have made 3 -4 prints. now constant service call code 0105 - checked all that the manual suggests...printhead and cut carriage and connection and disconnecting perfect, ran the limit initialize set up 10 times...

finally, we have the sp300v printing beautifully, yet about 60 percent of the time we get the 0105 code.....not exactly sure how to check all that the manual references...this has all come about since replacing print heads and blowing tons of fuses....that prob is resolved...now this...PLEASE...

Hi, so I have a versacamm sp330v, brand new heads and had all fuses and transistors replaced...Fuses continued to blow due to bad heads...New board is in, new heads are in...Not printing...Looking closer I see that there is no ink in the dampers or clear lines going to dampers and heads...Is...

I have determined after having Jemmings resolder my main board and both fuses blowing again that my printer heads are shorting...His thoughts as well. Is there anyone out there that can test print head to make sure that is the case before I buy new print heads, also where is the most affordable...

I want to see if perhaps the pump is dried on my roland...Again, we soaked the heads, the sprayed fluid through the heads with a syringe, sprayed perfect, ten re-assembled and now no ink...check fuses, all good now...seems like a clog upstream, maybe pump is dry? need to fix asap! joe

update, I checked fuses at main board, both we blown, f2, f3 - installed new fuses, did continuity test and now fine....still no ink on test print...when we do a power clean (5x) now, there is no fluid in container...it seems there may be air in the system? is there a way to flush system from...

We have a Roland SP 300V - we were starting to have blue overspray from the Black Blue head so we took the out and soaked in solution, then shot solution through the top cap and witnessed a nice even spray...We re- installed and now no ink at all...We have performed many powerfull cleaning to no...

I am trying to make some fine art prints using an epson water color paper...I used this paper with the epson 7600, and got great, clear vivid prints....with the new roland, the edges seem really soft and the color is not as vivid......any ideas? 1. is there a profile out there for the fine art...

my machine is finding 3 of the 3 crop marks, then send error message, crop mark not found......it is right there, any hints on helping the machine find it? media is 3m controltac with 3m lam......joeb

anyone use the bordeaux prime eco-sol inks in the fellers catalog? i wonder how they mix with the oem ecosolmax inks? any feedback? joe baker www.joebaker.net

Is is really important to wait some time between printing and laminating? and if so why? thanks in advance for advise - jOEb www.joebaker.net

i have an sp 300v - i am printing on avery gloss calendered, then laminating with an avery lam, re-loading....every time i am getting a "cropmark error - not found" error. the marks are there, and i see the printing looking for them, as well as registering around the circle mark....any ideas? my...

Any idea how to print on a 10"wide x 84" long media - everytime i try to load it gives me an invalid pinch roller location for the left clamp - i thought you can print on even 8.5 x 11 on this machine.....joe

i have a versacamm 300 - any idea how to make or where to get a catch bin for the prints as they come off the machine? i would like to make one if any has an idea...thanks in advance - jOeb http://www.joebaker.net