printhead

Hi I am searching for buy Xaar 126/35 pl print head for Infiniti 320b where I can buy?

Print head will not print yellow on test draw nor will it pump yellow. Moved the yellow damper to another print head and it filled the damper perfectly. Moved it back and nothing. The cyan pumps and prints during the test draw. I'm trying to determine if the print head is bad. If so do I need to...

I am looking for Mutoh 1324 printhead(s) I picked up a couple printers that had sat for a while, both function other than almost no ink at all coming from one, and only cyan and black working from the other with a hint of magenta and yellow. Ive tried cleaning, and its time to just buy a new...

Help! I am having trouble with my printer. The light cyan is not showing up at all. There are two print heads on this printer and all other colours are showing up great. The light cyan is from printhead B, yet the black, yellow, magenta, light magenta all work fine. The light cyan is completely...

Hey guys! I'm a new member of this forum, i have seen you post a lot helpful comments and great ideas of how to fix roland printers. The case is that i my XC-540 has started printing blurry. Printhead seems to be in a great shape excepted for the yellow one which has some reflected nozzles. When...

So I have an old printhead that got replaced for my cjv30-160, does anyone know of a place that would refurbish it?

hello my friends i know this is an old thread, but i have the same problem with my vj 1204, check the image, i buy a new print head whit a flat cables new and one kit of maintenance, i try print but E074 err Current Cr and the carriage stop in the middle of the printer, and later of reset the...

I've basically abandoned my DX5 based Mimaki JV33 for some time. The DX5 head was super clogged, the test print was mangled all over the place. There's even a visible "scratch" across the head. So I figure, what the heck, I'll pull the head off the machine and clean it real good. Using a fresh...

Hey guys and gals, anyone experience ink flood when the change head and fill ink? Its leaking somewhere behind pumps, trays full of black, what stayed behind as it leaked out the holes in case...where to begin looking???? Did I possibly "blowout" a line oor seal while I was clearing ink line...

A couple months ago I started losing black nozzles on my printer after a few head soaks and cleanings it was back to normal. It worked great for one print then just started dropping nozzles like crazy immediately afterwards. Ended up replacing the capping station, printhead, dampers and print...

After picking up a sc500 recently for a deal , (yes I know they are very old and have read most peoples opinions of the machine, but it is what it is, I run a small business from home). The previous owner replaced almost every consumable component except for the print heads, after setting up the...

Hiya, I'm after a dx7 printhead, preferably an older one with coding f and below, this can be found on the bottom of the sticker on the printhead. Very much appreciated, thanks in advance

Hey guys. I printed some signs last week and noticed there was magenta ink down the side of the printed vinyl which wasn't meant to be there. I then done a test print and the magenta and cyan is barely showing up on the print. I'll add some pictures to show. I tried cleaning group a print...

We purchased an HP Latex 560 back in April. We have not had any real problems with it; just a few user-created errors while we learn the machine. Now, I am getting concerned that it may be about time to replace some printheads, but I have no idea how to tell when I should. This is my current...

I have a HP Latex 310 printer. I was running 10 posters and on the last set of posters i noticed some banding in my prints. I immediately thought this might be due to a bad printhead. I ran a printhead alignment, printhead cleaning option and then ran the printhead plot. Here is a photo of...

Hello, Anyone on here know of a good Mutoh tech in the Houston/ south texas area, I am in need of a print head replacement, and it is something that i am not willing to do. I have had several issues with this printer and I have expended all possible options. I have replaced the pump assembly...

Hi, I have a Roland SC-500 printer and wanted to know what printhead type I have, for example, is it a DX2, DX3, DX4, etc. I'm getting mixed messages that it might be DX2 or DX3, but I need to know 100% for sure. My documentation does not tell me anything and I don't want to rip it out of the...

Hi, I have recently blown my heads trying to recover some bad nozzles. I need to order printheads from overseas (im based in Aus) as local costs too much. Im using Roland VersaCamm Sp540i but the listing for part number (1000002201) sign-in-china listings say its not for my printer. Can you...

Wondering if anyone has been able to bring a Summa DC4 printhead back to life after a "blown pixel" diagnosis. I have a DC4sx we just brought in from our warehouse that hasn't been operating for several years I'd like to get back in our shop workflow. Done all the particulars to clean...

Looking for purchase of a manifold for my DX5 print head. I need the part asap and am looking for a US vendor. International may take too long to arrive. Mutoh VJ1204