Search results

Is there a setting to adjust the gap between print jobs? We recently bought a SureColor S60600 and are getting a 10-12in gap between jobs. It appears to roll the substrate out in order to complete drying the job, but then doesn't roll back after drying like our HP does.

I tried printing on the roll setting for the first time and things went smoothly, but now that I am trying to print on rigid material again (4mil coroplast) the machine will not measure the width of the media properly. It measure the entire length the machine allows instead of the 48 inches that...

We've been getting error code 16.13:10 for a few weeks now. We would restart the printer and it could be fine for a week and then pop up again. Yesterday we got the same code, so we took the front cover off and cleaned the dust out of the fans with canned air. There was A LOT in there. After we...

Our VS-540i is not printing anything. We have replaced the cap, printhead, and dampers. We changed the head rank numbers, reset the head group, run powerful cleanings, etc. Ink is definitely moving. I've pulled ink with a syringe through the bottom of the cap and checked to make sure the new...

We just started getting these lines in our prints on the HP Latex 310. Only horizontal. It's like the negative space "casts a shadow". I'm attaching some pictures. It doesn't matter if we rotate the file before printing. We have changed the printheads too. Any ideas?

Ever since I have started working with this UV printer I have noticed that it does not print the images straight on the material. I use 4 mil chloroplast for most of my signs and the issue comes in with double sided signs. When cutting the signs out you can clearly see that the machine is not...

We are learning how to use our relatively new Roland LEJ 640 hybrid printer. When printing a full 4x8 sheet we sometimes have a series of head swipes, not hard strikes, with the passing of the head over the very exact middle of the sheet. The marks might cover an area of 6" x 8" and no more...

I have a customer who insist on using a sunbrella type fabric for pole banners. How well does the latex adhere to the fabric and what is a good source for the fabric? I normally use 13 oz scrim and they don't want to use a canvas like product. They are convinced that it will last for 3-5...

We make a lot of real estate signs. We have commonly used a regular wood bit for drilling holes but, as you know, it leaves rough edges. What bit gives a clean, sharp-edge to the hole? It will be used in our drill press.

The cutting has been staggered as you can see from photo. holder is clean and the blade new. Does this with other files as well. Wondering what the other solutions there might be. Staggers are not consistent in distance.

Does anyone have any thoughts on what might cause the red in my latex 310 to bleed like this? This is a file and substrate we print on a regular basis. I have run all test plots, checked printheads, changed out ink cartridges, changed to another roll of substrate, but nothing seems to have any...

Can anyone help me identify the font that "ALABAMA EDUCATION ASSOCIATION" is in? I know its something common, but it's escaping me at the moment. Thanks!

Can anyone Identify the font used in the words "MOD SQUAD" and "CLOUD CHASERS"? Thanks in advance!

I am looking for a scrim(?) #banner material that doesn't need to be hemmed. A client brought in a small banner and asked us to reproduce the look, and it was a normal banner material but did not have any hems and did not seem to be curling. Any suggestions??

who knows the font for "event society"? Looks familiar but I can't put my finger on it.

We recently upgraded to the VS540i and have found a buyer for our SP540v. Does anyone know any specifics on how the printer should be packaged for safe delivery? I understand I should get some cleaning cartridges and drain all the ink out of the lines, but I'm not sure how that would work with...

I have seen this coming up more and more lately. Seems that about every 12-18" I get a faded looking streak that is about an inch wide. What is this? Could this be a pump issue? I have attached a photo showing what is happening.

Anyone had any experience with the bulk system from Supply55? We are printing with a Roland Versacamm SP540 with eco-sol inks. Price is good for a horizontal cartridge setup. :thankyou:

I have been having a problem with the 100% black smearing even after 24 hours. I am wondering if the coverage is so dense that the ink will not thoroughly set. What will the "density level" adjustment in Versaworks do to coverage? I am using EcoSol Max inks and compatible media. Are there other...