latex

I recently got this message when I fired up my Onyx Postershop 12. "Network I/O is limited. Anti-virus software may be blocking access. Other network problems may exist." I don't know if this contributes to my jobs being cancelled in the middle of printing. It's kinda weird, because it only...

All of a sudden, I started getting wet spots on my prints. Doesn't matter what material I use. It looks like it's always in the same area...towards the right of the printer (if you're looking at printer). See picture.

I wonder if I can ask for some help... HP latex 260. I keep getting this "Maintenance #3 contact support" message and it won't print what the RIP sends. It is waiting to be fixed. I can to a head test print ok. Looks good. The funnel is now clean. The waste bucket is new . The air filter and...

While printing long job, material becomes crumpled under the rollers. Material - syntetic canvas (230-260 g/m2), 1.52 m width. Not at the start but may be at the roll half. And somewhere at the width center. Bumps appear on the material and then printing head begins th scratch it. Only stopping...

Hello all, So I got this mimaki jv400LX / Ricoh l4160 to start printing again but i can’t get a clean print when I use black or dark colors. It tends to “over spray” darker colors AND the orange and black test prints are crooked for some reason. Apparently the black losing the bottom right...

Every time I load a roll, my Onyx RIP synchronizes with the printer with the correct media type, but NOT the size. I loaded a 54" roll, and it says it is a 56" roll. Any ideas why it's doing this?

I'm trying to work my way into the printing business but I had no idea how much there was to know about it. I have a more than full time business now but it's quite physically demanding and on my next birthday I'll be hitting the big SIXTY mark. I thought the garment decorating business would...

Does anyone knows where can I buy trailing cable for HP Latex 360. The authorized service is asking 2500 $ for cable and to replace it.

Hi, usually after printing darker graphics, I notice a lot of squiggly like debris on the print. I don't believe these are consistent spots. I downloaded and used the Orajet printer profile while printing in Caldera. Printer: HP Latex 260 Substrate: Orajet 3621 What are some tips on how to...

Where: PIP Marketing/Signs/Print 8325 N. Allen Road Peoria, IL 61615 Position Overview: This a production position using the latest in printing and CNC router technology. You will be printing, cutting, routing, and installing all kinds of things. No two days will be the same that is for sure...

Newb here to large format (screen print background) but we're putting together an innercity middle school print shop afterschool program. 100% committed to HP 115, but I'm wondering about opinions on the Print & Cut solution, and I'm not seeing any in the forum (and I'm betting somebody will...

Hey all, I'm having a problem that I just can't seem to figure out. It randomly goes out of alignment and then prints fine. I have cleaned and oiled the carriage rails, cleaned the encoder strip, checked the belt and the gear drive for debris, ran a vacuum check, realigned the print heads and a...

Hi all, I'm new to the forum and just wanted to say hi and ask what everyone recommended for media on the HP L25500. I'm not new to printing, but I am new to latex. I haven't had a large demand for printed graphics so up until now I have done all of my signs and banners the old school way with...

I've recently picked up a HP L25500 60" latex printer, and I'm having issues with the second print looks like it runs out of cyan. If I let the printer sit (off) overnight, the next day, it goes back to normal for the first print (or I should say, for the first few feet, I haven't printed much...

Hey all, Just looking for some suggestions. I've been spending some time building media profiles on our HP Latex 370 printer, and it seems that no matter what I set my passes, vacuum temperature, dry temperature, and/or optimizer levels to, I just can't get areas of small-ish text (6-18 pt) to...

We have been having issues trying to print on Tekra Jetview using the HP570 (Latex). Everytime. We encounter headstrikes everytime. It appears the Jetview is being affected by the heat; the material 'bows' up causing the headstrikes. Yet, when we turn the heat down, the ink does not cure. Has...

Anyone have any idea why my L25500 would be printing like this? Its been working fine so far, though it has taken me a while to figure out all the right temperatures for every different vinyl, this was printing on GF203 vinyl at 16 pass with 220 drying temp, 235 curing temp, and 35 for vac. I...

Looking for a reflective banner media. preferably a 36"/38" or 63" width. Latex preferred but Eco-Sol acceptable I am sure double-sided printing is asking for too much, but I do believe in Santa Claus and Unicorns. I have a customer that was perfectly happy with the boulevard banners were...

We recently purchased a new latex 365 from BigFish here on Signs101. I've waited a few years due to some horror stories about the latex and I understood that it was new tech that could take time to build a great printer. My friend Justin has a signshop and he uses all HP equipment for this...

Is the extra $ worth it, to get the 365 over the 335? I'll be focusing on Stickers, at least in the beginning (die cut). As a reference, like the ones Sticker Mule does. I'm thinking either printer + a Graphtec FC8600 54" to start with. Haven't completely discarded the 115 either. All input...