print

I have a job coming up where this guy wants me to scan an old photo of his father into digital format and then print it wide format... this I am already setup however I had my vendor send me samples of Sihl 3699 Photoart and then GF Concept 106 optically clear mounting film. The issue I am...

Mutoh 1624. Been having a sporadic problem with the large fields of color (solid or gradient) coming out with slightly different tones from panel to panel. Looking at it close you can see the print pattern very tight and clean on a panel and the next will have a very grainy look to it causing...

I'm using Onyx to rip graphics to my HP Scitex FB500. When I try to use the Max DPI Saturated mode, the entire image (including the white areas) will have a dark yellow cast. This began at some point while another guy was running our vinyl/print department and I was in a different department...

I have a Mimaki CjV150 and theses lines appears each side of the print someone know why ?

need advise , running machine perfect, disconnect it due storm lights, when i turned it on again to start working bumps this errror msg !car (#01) cartridge m-- ,try to print and send a msg , an ink error ocurs, i have the refillable ink system by t way. all comments are welcome ! thank you...

Hi all. Not new to Signs101 was a member way back when (well some years ago now. And have just returned as i need some bed time reading. and to help were i can. I have been in the Garment Gift and Large Format printing for just over 14 years. and have used most print methods along the way...

Vg540, 4 weeks old. I calibrate to have perfect cuts then print 5 6x8 sheets across twice. And now look at how the print test looks. What am I doing wrong? I have tried a new roll of Orajet 3621, reloaded, with only 2 pinch rollers, 4 rollers, changed temps and I can't figure out why after...

So I've had this 330 for 2+ years and I'm really all thumbs. I want to put a disclaimer out there and say that we're not the shop that makes custom profiles. In fact, we usually stick to 1 profile for all vinyl, 1 or 2 for textiles and 1 for banner and thats it. We'll do the print tests and...

Calling all digital print wizards, I'm wondering if this type of print is possible, and will look good, if done on clear? White flood coat then print. The hard part would be getting the gradient in the reflection to look good. Client really wants a reflection, and it's the only thing I can...

every so often when i'm printing, a weird anomaly happens. As you can see by the photo (forgive my not spell checking the photo) there is a really thin line across the print. the line also goes thru the white areas that receive no ink. Also if you look close, there looks like an offset in the...

Guys! I seek your years of experience with different products and solutions. We are a mini print shop equipped with a graphtec fc3100-120 and we now want to expand into full color stickers making. The machines that can do both print and cut that I've seen are superduperWTF expensive=) Does...

I have a VP 540 printer, I notice that when I print a colored print the machine will stop on 4 or 5 passes an will say, Not connected. But when I just do a cut job it runs fine. I have change the IP address on the machine and on my laptop when it comes to printing. I am connect with a cable, no...

Hi all, Got a CJV150 we've had for about 3 months and every time I do a Print & Cut job the X origin seems to be out. Y doesn't seem to vary. I've run the P&C Origin Adjust several times and often have to re-run it after the next job I send cuts out of the print... I'm only setting the 720dpi...

We have a roll of Alumigraphic material, the Grip version. When we got the roll we were able to print a few jobs (one being a sample print in front of our front door). Now that we have gone into the roll a bit, I am having issues loading and running this stuff on our Latex 260. Head strikes and...

Hi, i have started doing color change wraps three months ago and i have 6 cars fully wrapped so far and now i have two customers, one with boat and another one with mini van, who needs commercial graphics. I can do the design, but i don't know if there is a place where i can order prints online...

I'm trying to print/cut some decals and where the rollers hit the red its picking it up and transferring the ink up/down the print. Its only the red ink for some reason. Any ideas? I have my heat all the way up

The last couple of times we've tried to print on 5600 white reflective, the print looks "smeared". We have a mimaki jv3. Any suggestions/ideas? Thanks in advance

I have a Mimaki CJV30 and just recently it has developed a small strange problem. Attached are some pictures. Basically when I print black, there is a cyan overspray. This only happens on black and horizontally, see "L" shape mark to understand what I mean by horizontally. This has been...

I need a print supplier for my graphics. I design and mockup proofs and get everything print ready. Just need someone to supply the RTA graphics. Need a quote for this. Will be 2 bottom graphics same size and the cut logo and text. Front Door Proof.jpg - Google Drive Thanks!

I've upgraded from the 360 to a 570 but I'm not liking it. on the 360 i had wallpapers printing all day, where as on the 570 i just can't get the settings right on all kinds of materials but mainly papers and wallpapers it seems like theres just way too much heat now. I've been trying to print...